
SAMIL 100
strict warning: Declaration of views_attach_plugin_display_node_content::options_submit() should be compatible with views_plugin_display::options_submit(&$form, &$form_state) in /usr/www/users/dtmcorqxcn/sites/d-t-m.co.za/modules/views_attach/views_attach_plugin_display_node_content.inc on line 248.

SAMIL 100 - (MAGIRUS DEUTZ 320D21AL)
ENGINE | |
Type: |
Deutz F10L 413F direct injection normally aspirated air cooled |
Cycle: |
4 stroke |
Cylinders: |
10 arranged in vee formation 90deg. apart |
Bore Stroke: |
125 mm x 130 mm |
Displacement: |
15953 cc |
Max power: |
235 kW @ 2500 r/p |
Firing order: |
1,10,5,7,2,8,3,9,4,6 |
Idling speed: |
600 r/min |
CLUTCH | |
Disc diameter: |
420 mm |
Disc thickness: |
10.8 mm |
Method of operation: |
Hydraulic self adjusting |
GEARBOX | |
Gearbox type: |
ZF S6-90 6 speed synchromesh |
Input rating: |
850 Nm |
Mass: |
225 kg |
Oil capacity: |
13 l. |
TRANSFER GEARBOX | |
The output drive from the transfer gearbox is continuously coupled to the front and rear axles. A differential is incorporated in the transfer box to adjust for differences in front and rear axle drives. | |
High range ratio: | 1.095 : 1 |
Low range ratio: | 1.767 : 1 |
Longitudinal lock and high/low selector are pneumatically actuated | |
AXLES | |
Front axle: | Banjo housing type driving axle with steer-able, hollow stub axles driving trough planetary reduction in wheel hubs. |
Axle ratio: | 3,103 : 1 |
Hub reduction ratio: | 1.85 :1 |
Overall reduction ratio: | 5.74 :1 |
Differential lock: | No |
Rear axle: |
Banjo housing type driving axle with planetary reduction in wheel hubs |
Axle ratio: |
3.111 : 1 |
Hub reduction ratio: |
1.867 : 1 |
Overall reduction ratio: |
5.808 : 1 |
Differential lock: |
Yes – pneumatically actuated |
BRAKES | |
Service brakes: |
Dual, full air |
Parking brake: |
Spring actuated, acting on rear wheels |
Exhaust brake: |
Pneumatically operated on both exhaust manifolds by foot control valve |
SUSPENSION |
|
Semi – elliptical leaf springs front and rear axle. | |
The center of rear springs are secured to trunnion bearings and the ends of springs support the axle on slipper pads | |
Shock absorbers: | Two hydraulic double – acting, telescopic shock absorbers are fitted to the front axle. |
ELECTRICAL SYSTEM | |
Batteries: |
2 x 12V 120 A/h |
Starter: |
Bosch 24V |
Starter output: |
6.6 Kw |
Alternator: |
Bosch 28V,35A |
STEERING | |
Hydraulically assisted by engine driven hydraulic pump. | |
TYRES | |
Tyre size: |
1400 x 20 x 18 ply |
Single wheels are fitted to all six hubs | |
DIMENSIONS | |
Wheelbase: |
5250/1380 mm |
Front wheel track: |
2002 mm |
Rear wheel track: |
2048 mm |
Total length: |
9248 mm |
Total width: |
2500 mm |
Total height: |
3000 mm |
Ground clearance - front: |
355 mm |
Ground clearance - rear: |
359 mm |
Fuel tank capacity: |
2 x 200 Lt |
Max speed: |
90 km/h |
Angle of approach: |
32 deg |
Angle of departure: |
28 deg |
SUGGESTED SPARES KIT | |
2 X Air Filters (Inner & Outer) | 2 X Fuel filter |
2 X Oil-filter | 10 X Tappet cover gasket |
2 X Handbrake booster | 1 X Un-loader Valve |
1 X 4 Way Valve | 20 X Wheel stud & Nut |
2 X Front Hub Seals | 2 X Front Side shaft seals |
2 X Rear Hub Seals | 2 X Rear Side shaft Seals |
2 X Front Inner & Outer Hub Bearing | 2 X Rear Inner & Outer Hub bearing |
1 X Alternator | 1 X Clutch Kit |
2 X V-Belt Compressor | 2 X V-Belt Alternator |
4 X O-Ring Rear Diff | |
WARRANTY | |
Drakensberg Truck Manufacturers (Pty) Ltd warranty against defective material and workmanship. The direct cost of rectifying defective material or workmanship shall be borne by DTM. However, the cost of transportation, accommodation and subsistence will need to be covered by the customer. Work done on the vehicles by other than our approved service agents will negate the warranty. Wear and tear and the carrying out of routine maintenance is the end user’s responsibility and is not part of the warranty. Failure to carry out recommended routine maintenance will negate the warranty. Drakensberg Truck Manufacturers (Pty) Ltd does not accept liability for any consequential losses arising from any cause, whatsoever. |
|
REMANUFACTURED | |
The truck is stripped to the last bolt, every component rebuilt to factory specs using only genuine factory parts; the cab is finished to brand new specification including interior and wiring. New tyres are used; warranty is for 12 months or 100 000 km on the main assemblies. Registration and R.W.C. supplied. | |
Engine: Asses engine to confirm low mileage & excellent basic conditions |
|
Clutch: |
|
Gearbox: |
|
Axles: |
|
Steering System: |
|
Prop shafts: |
|
Suspension: |
|
Electrical System: |
|
Brake System: |
|
Bodywork & Chassis: |
|
Wheels & Tyres: |
|
Interior trimming: |
|
Bookmark/Search this post with
Contact Us
Plot 145 Wallmansthal
Pyramid District
Pretoria
Gauteng Province
South Africa
0120
Reception: 087 751 0440
Fax: 086 661 4627
Email: info@d-t-m.co.za
PLEASE CONTACT US FOR MORE DETAILS
Copyright © 2014 Drakensberg Truck Manufacturers. All rights reserved. Built by Kuberfirma