DTM product slideshow image
DTM product slideshow image
DTM product slideshow image
DTM product slideshow image

SAMIL 50

A DTM product image

SAMIL 50 MKI - (MAGIRUS DEUTZ 192D12 AL)

REMANUFACTURED Cab (soft skin) & Chassis
Drop Side Load Body (Supply & Fit)

ENGINE
Type:
 Deutz F6L 413F direct injection normally aspirated air cooled
Cycle:
 4 stroke
Cylinders:
 6 arranged in vee formation 90deg. apart
Bore Stroke:
 125 mm x 130 mm
Displacement:
 9572 ccm 
Max power:
 141 kW @ 2500 r/p    
Firing order:
 1,6,3,5,2,4
Idling speed:
 600 r/min
 
CLUTCH
Clutch type:
 GFM 350K
Disc diameter:
 350 mm
Disc thickness:
 10.8 mm
Method of operation:
 Hydraulic self adjusting
 
GEARBOX
Gearbox type:
 ZF S6-65  6 speed synchromesh
Input rating:
 650 Nm
Mass:
 240 kg
Oil capacity:
 11 l.
 
TRANSFER GEARBOX
Transfer box type: Z65
The output drive from the transfer gearbox is continuously coupled to the front and rear axles. A differential is incorporated in the transfer box to adjust for different ratios (or slippage) between front and rear axles. The by longitudinal lock when road surface conditions are poor (ie., loose, or slippery)
High range ratio: 1.032 : 1
Low range ratio: 1.783 : 1
  Longitudinal lock and high/low selector are pneumatically actuated
 
AXLES
Front axle: Banjo housing type driving axle with steerable, hollow stub axles
Axle ratio: 6.33 : 1
Differential lock: No
Rear axle:
 Banjo housing type driving axle with planetary reduction in wheel hubs
Axle ratio:
  4.125 : 1
Hub reduction ratio:
 1.524 : 1
Overall reduction ratio:
 6.29 : 1
Differential lock:
 Yes – pneumatically actuated
 
BRAKES
Service brakes:
 Dual, full air
Parking brake:
 Spring actuated, acting on rear wheels
Exhaust brake:
 Pneumatically operated on both exhaust manifolds by foot control valve
 
SUSPENSION
Semi – elliptical leaf springs front and rear axle.
Torsion bar stabilizer is fitted to the rear axle.
Shock absorbers: two hydraulic double acting, telescopic shock absorbers are fitted to the front and rear axles.
 
ELECTRICAL SYSTEM
Batteries:
 2 x 12V 120 A/h
Starter:
 Bosch 24V
Starter output:
 4.4 Kw
Alternator:
 Bosch 28V,35A
 
STEERING
Hydraulically assisted by engine driven hydraulic pump.
 
TYRES
Tyre size:
 1400 x 20 x 18 ply
Single wheels are fitted to all four hubs
 
DIMENSIONS
Wheelbase:
 4900 mm
Front wheel track:
 1985 mm
Rear wheel track:
 2030 mm
Total length:
 7853 mm
Total width:
 2450 mm
Total height:
 3000 mm
Ground clearance - front:
 355 mm
Ground clearance - rear:
 355 mm
Fuel tank capacity:
 2 x 200 Lt
Max speed:
 95 km/h
Angle of approach:
 36 deg
Angle of departure:
 33 deg
 
BASIC SERVICE KIT
1 X Set of filters (air, oil & fuel)
1 X Set of fan-belts(alternator & compressor)
4 X Tappet cover gaskets
 
 
SUGGESTED SPARES KIT
2 X Air Filters (Inner & Outer) 2 X  Fuel filter
2 X Oil-filter 6 X Tappet cover gasket
2 X Handbrake booster 1 X Un-loader Valve
1 X 4 Way Valve 20 X Wheel stud & Nut
2 X Front Hub Seals 2 X Front Side shaft seals
2 X Rear Hub Seals 2 X Rear Side shaft Seals
2 X Front Inner & Outer Hub Bearing 2 X Rear Inner & Outer Hub bearing
1 X Alternator 1 X Clutch Kit
2 X V-Belt Compressor 2 X V-Belt Alternator
4 X O-Ring Rear Diff  
 
WARRANTY
Drakensberg Truck Manufacturers (Pty) Ltd warranty against defective material and workmanship. The direct cost of rectifying defective material or workmanship shall be borne by DTM. However, the cost of transportation, accommodation and subsistence will need to be covered by the customer. Work done on the vehicles by other than our approved service agents will negate the warranty. Wear and tear and the carrying out of routine maintenance is the end user’s responsibility and is not part of the warranty. Failure to carry out recommended routine maintenance will negate the warranty.
 
Drakensberg Truck Manufacturers (Pty) Ltd does not accept liability for any consequential losses arising from any cause, whatsoever.
 
REMANUFACTURED
The truck is stripped to the last bolt, every component rebuilt to factory specs using only genuine factory parts; the cab is finished to brand new specification including interior and wiring. New tyres are used; warranty is for 12 months or 100 000 km on the main assemblies. Registration and R.W.C. supplied.
 
Engine:
Asses engine to confirm low mileage & excellent basic conditions
  • Remanufactured to factory specification
Clutch:
  • Fit new OEM clutch assembly
  • Fit new master & slave cylinder
  • New Clutch hydraulic line
Gearbox:
  • Remanufacture to factory specification
Axles:
  • Remanufacture to factory specification
Steering System:
  • Remanufacture to factory specification
Prop shafts:
  • Fit new prop shafts
Suspension:
  • Remanufacture to factory specification
  • Fit new needle bearings
  • Fit new shackle pins
  • Retention front and rear springs sets
  • Fit new rear stabilizer bushes
Electrical System:
  • New wiring looms
  • New starter
  • New alternator (Bosch)
  • New wiper motor
Brake System:
  • Remanufacture to factory specification including all air piping/tubing
  • New brake shoes & drums
  • All new air valves fitted
Bodywork & Chassis:
  • Paint to customers colour specifications
  • Chassis colour – Grey
  • Chassis: sandblast, clean, inspect,  Re-spray
  • Chassis: inspect for defects
Wheels & Tyres:
  •  New
Interior trimming:
  •  New

Send us an enquiry

Bookmark/Search this post with:
  • Digg
  • Facebook
  • Google
  • Yahoo